Robinair 17700 Manual
39 Troubleshooting Guide Use the following chart to identify possible causes for system operating problems during the recovery process and to determine possible solutions. RECOVERY OPERATION Recovery compressor does not start Cause: Main Power switch off Cure: Turn on Main Power switch Cause: Power cord not plugged in or no power at plug Cure: Check circuit for power Cause: “Full” on digital display Cure: Change the tank according to the instructions in “Installing a Refillable Refrigerant Tank” Cause: “Hi-P” on digital display Cure: Check the valves on the tank to be sure they are open. Check the air purge indicator.
2 ORIGINAL Models 1/17703 Service Manual Theory of Operation and Safety Precautions The 17700 Series recovery, recycle, evacuation and recharging units are designed to be used for. Robinair 18192 R-134A Manual Replacement Coupler Set. For Robinair 17700-2K, 34134A, 34134-2K, 342000, 34234, 34300-2K, 34700, 34700-2K, 34700Z.
If the green needle exceeds 275 psi, open the air purge valve until the pressure reaches 225 psi.
. 180 Answers SOURCE: It seems to be your last calibration was not correct! For Robinair Model-34700z scal calibration follow as bellow: Form the main menu go to 'CHANGE DEFAULT' then press 5454 & YES key (passwoed to access default option).Once you enter to default menu,go to 'SCALE CALIBRATION' & press YES key. Now follow the on screen text. NOTE:you should have 9KG/20LBS of weight for scale calibration. Do not change 'TANK TARE'. It must be on factory setup 16.30 lbs OR 7.40 kg.
Hope this will help you to solve thr problem & if my solution is useful to you please vote for it Posted on Aug 15, 2010. 180 Answers SOURCE: Robinair Model-34700Z scal calibration follow as bellow: Press main menu then press up or down arrow till scree appear 'CHANGE DEFAULT' then press 5454 from the keypad & then YES key (passwoed to access default option).Once you enter to default menu,go to 'SCALE CALIBRATION' & then press YES key. Now follow the on screen text.
Once you calibrate scale then press STOP key to exit. NOTE: You should have 9KG/20LBS of weight for scale calibration. Do not change 'TANK TARE' or any other setting it must be on factory setup. Hope this will help you to solve the problem & if my solution is useful to you please vote for it Posted on Apr 05, 2011. Please check Charging solenoid (S3) in Solenoid manifold block, it may need to change solenoid coil or Rebuild. If charging solenoid is OK, then problem can be SCALE or MAIN CIRCUIT BOARD. See if the machine display show default charging weight 90 kg/lbs when you active CHARGE mode.
Robinair 17700 Manual Scale Calibration
If not then calibrate scale. But if default charging weight is shown then replace MAIN CIRCUIT BOARD. See attached picture to find solenoids. I wish this will help you to solve the problem.
If so please vote for it for further assistance. Best of luck! May 13, 2011. Robinair Model-34700Z scal calibration follow as bellow: Press main menu then press up or down arrow till scree appear 'CHANGE DEFAULT' then press 5454 from the keypad & then YES key (passwoed to access default option).Once you enter to default menu,go to 'SCALE CALIBRATION' & then press YES key. Now follow the on screen text.
Robinair 17700 Manual
Once you calibrate scale then press STOP key to exit. NOTE: You should have 9KG/20LBS of weight for scale calibration. Do not change 'TANK TARE' or any other setting it must be on factory setup.
Hope this will help you to solve the problem & if my solution is useful to you please vote for it Apr 04, 2011. Robinair Model-34700Z,for scal calibration follow as bellow: Form the main menu go to 'CHANGE DEFAULT' then press 5454 & YES key (passwoed to access default option).Once you enter to default menu,go to 'SCALE CALIBRATION' & press YES key. Now follow the on screen text.
NOTE:you should have 9KG/20LBS of weight for scale calibration. Do not change 'TANK TARE'. It must be on factory setup 16.30 lbs OR 7.40 kg. Hope this will help you to solve thr problem & if my solution is useful to you please vote for it Aug 27, 2010. It seems to be your last calibration was not correct!
Robinair 17700 Service Manual
For Robinair Model-34700z scal calibration follow as bellow: Form the main menu go to 'CHANGE DEFAULT' then press 5454 & YES key (passwoed to access default option).Once you enter to default menu,go to 'SCALE CALIBRATION' & press YES key. Now follow the on screen text. NOTE:you should have 9KG/20LBS of weight for scale calibration.
Do not change 'TANK TARE'. It must be on factory setup 16.30 lbs OR 7.40 kg. Hope this will help you to solve thr problem & if my solution is useful to you please vote for it Aug 15, 2010.